AJP Factory Accessories – Available Now!!!
Please contact your AJP Dealer to purchase…..

Rear Fender Rack – fits all PR3 and PR4 models. Hi-quality brushed stainless steel rack, custom made for AJP. Includes all mounting hardware needed as shown. Some drilling of the fender is required. MC1019 – $99

Race CDI – fits all PR3 and PR4 models. Direct replacement for stock CDI. Improves throttle response and raises rev limit. MC1018 – $30

Factory Power-Up Kit – Fits all 240cc PR3 & PR4 models. Includes camshaft, bearing, o-ring, plus carb jets. Provides a noticeable increase in power. We recommend combining this kit with either our FMF or Belparts exhaust system in order to maximize the power benefits. 00MTS01A0172 – $298

Show your colors! AJP Factory Banner. Measures 8 feet long x 1 foot high. Made of heavy duty material with grommets on 4 corners as well as along length bottom and top. MC1017 – $45
![IMG_1547[1]](http://motoajp.com/wp-content/uploads/2015/05/IMG_15471-1024x1024.jpg)
MX Race Kit to fit the PR3 & PR4. Includes racing wire harness, on/off kill switch, front number plate, and number plate bracket. Eliminates all lighting, meter, and switchgear – which results in a weight savings of over 4 pounds! Combine this kit with a lithium battery and our billet footpegs to save a total of 9lbs! MC1015 – $189

38 tooth Aluminum rear sprocket to fit the PR3 models only. This sprocket is 1.5lbs lighter than the stock rear sprocket offering a noticeable reduction in unsprung and rotational mass! Also lengthens the gearing slightly by 1 tooth less than stock – offering a slightly higher top speed in each gear. MC1014 – $79.99

FMF PowerCore 4 Spark Arrestor Muffler built to fit our PR3 & PR4. Includes all mounting hardware – slips right on to stock attachment points. USFS approved screen type removable spark arrestor included. This muffler flows better than our stock muffler – resulting in an improvement in power and throttle response. MC1011 – $359

EFI tuner for 2013 and newer PR5’s. An “Electronic Jet Kit” for your bike! Tune richer or leaner in 3 throttle ranges – idle/light cruising, acceleration, and wide open – plus modify the set point for when each range comes into play. Comes complete with instructions – very E-Z to install. Stays with the bike – allows tuning on the fly while the bike is running. MC1010 – $225

Magura Hydraulic Clutch Kit – Fits PR3 & PR4. Provides a very consistent clutch feel and engagement point at all times. Comes completely assembled and pre-bled, ready for E-Z install. Also features the backwards bending clutch lever feature from Magura – no more broken clutch levers! MC1003 – $335

Aluminum Exhaust Heat Shield to fit the PR5. Shrouds mid-pipe from contacting rider. 00MTS04A0054 – $99

High Performance complete exhaust system with resonator style header to fit the PR3 & PR4 – Boosts Torque & Improves Throttle Response – 00MTS04A0053 – $499
![IMG_0919[1]](http://motoajp.com/wp-content/uploads/2015/05/IMG_09191-1024x1024.jpg)
AJP Team hat – just like the Factory guys wear! One size fits most with adjustable Velcro strap in rear. MC1007 – $19.95

AJP Factory Foot Pegs. Red Anodized Billet Aluminum with Stainless Steel grip inserts. Weighs .6lbs less than the stock pegs! Uses stock mounting hardware, fits all AJP models – PR3 thru PR5R. 00QUS03A0037 – $99 pair

Factory rear suspension link – lower the seat height of your stock PR3 or PR4 by 1 full inch! Results in a new seat height of 33.5 inches on a PR3 and 35.5 inches on a PR4. Shorter side stand (00QUS04A0044) is recommended for the PR4 application. Some PR3’s will need the stock side-stand bracket lightly modified to allow the bike to lean correctly with this link installed. 00STC07C0004 – $99.
![IMG_0943[1]](http://motoajp.com/wp-content/uploads/2015/05/IMG_09431-1024x1024.jpg)
Shorter side stand – fits PR4. Works perfectly with our Factory lowering link, or use it alone to give your stock 2014-2015 PR4 a bit more lean when parked on uneven terrain. 00QUS04A0044 – $49.

Magura Hydraulic Clutch Kit – Fits PR5 & PR5R. Dramatically lightens the clutch pull compared with stock cable set-up, plus auto-compensates – so no lever adjusting is ever needed! Comes completely assembled & pre-bled, ready for E-Z install. Also features the backwards bending lever feature, so no more broken clutch levers! MC1006 – $335.

PR5 Radiator Guards – complete kit to “cage” both your PR5 radiators. All Aluminum construction with Stainless Steel hardware – 00MTS01A0160 – $119.

Screen Type Spark Arrestor to fit PR5 with stock AJP muffler (NOT DOMA). Replaces stock insert – slight noise increase from stock, larger opening for more power, weighs .5lbs lighter than stock AJP insert. MC1002 – $40.

Red Silicone hose kit for PR5 & PR5R – includes all 4 hoses. Dress up your PR5 and keep your cool! MC1013 – $50

PR5 Titanium DOMA Muffler & Mid-Pipe with Factory AJP header. Full system – ready to bolt on. Lighter than stock by 1 lb plus adds 3hp! The Ultimate PR5 upgrade. Consists of 00MTS04A0031 & 00MTS06A0057 = $899.